:Our 5800 test tips serie is built according to the IEC 61010-031 standard requirements. Their achievement needs a supplementary enclosure which prevents persons against access to hazardous parts with their fingers : IP2X.
| IP2X test probes |
IP2X test probes,
with high breaking capacity fuse :
|
 |
||
 |
Class CC fuse-holder test tip, Ø4 mm connectable tip - Ø4 mm female connector. P / N 5801-CC. |
|
Example of
standard fuse-holder test tip lead, |
Specifications (details lower) :
Electrical specifications :
set by the fuse
)
Fuse-holder test tips available in standard or class CC version :
(recognizable by their rejection feature), US
standard
, European standard Thanks to the anti-error device of these fuse-holder test tips, it is impossible to install a standard fuse in a class CC fuse-holder test tip.
| 10 x 38 mm (0.41 x 1.50 in) fuse specifications | 10 x 38 mm (0.41 x 1.50 in) standard fuses | 10 x 38 mm (0.41 x 1.50 in) class CC fuses |
| Voltage : | 500 V | 600 V |
| Currents range : | 2 A, 6 A, 10 A, 16 A, et 20 A | 2 A, 6 A, 10 A, 15 A, et 20 A |
| Breaking capacity : |
120 kA (120 000 A) |
200 kA (200 000 A) |
| Design : | (symmetrical) |
Anti-error device (rejection feature) |
| Light indicator of blown fuse : An orange neon indicator lights when the fuse is blown. |
 |
| Long and fine tip : The length (26 mm, 1 in) and the fineness (Ø3.8 mm, 0.15 in) of the tip itself allow measurements in well bottom to 26 mm (1 in). |
 Retracted sleeve |
Thanks to its sleeve specially designed, the test tip can be safely connected to
range (
) It can be also connecte to basic Ø4 mm female sockets
generally limited to non hazardous live voltages 33 V~ / 70 V
.
| Easy handling with gloves |  |
Several types of available connections (in addition of Ø4 mm connectable tip) :
Available versions :
| Class CC or standard fuse-holder test tip, with or without fuse |
| Ends of the fuse-holder test tip : |
| Ø4 mm connectable tip | Ø4 mm female |
P / N 5801-Sd (standard version) or P / N 5801-CC (class CC version) |
| Ø4 mm connectable tip | cable with |
|
Type 5807-Sd (standard version) or Type 5807-CC (class CC version) |
| Fuse-holder test tips shipped
with cover unlocking special tool. As required by the standard, for safety reasons, the cover can not be opened manually, and a special tool is required to open cover and replace fuse. |
|
Other specifications :
 |
 |
||
|
Test tip, Ø4 mm connectable tip - Ø4 mm female connector. P / N 5802. |
|
Test tip lead, Ø4 mm connectable tip - Ø4 mm male right angle connector. P / N 5812. |
Specifications (details lower) :
Electrical specifications :
or 600 V, measurement category IV (CAT IV) )
| Long and fine tip : The length (26 mm, 1 in) and the fineness (Ø3.8 mm, 0.15 in) of the tip itself allow measurements in well bottom to 26 mm (1 in). |
Retracted sleeve |
Thanks to its sleeve specially designed, the test tip can be safely connected to
range (
) It can be also connected to basic Ø4 mm female sockets
generally limited to non hazardous live voltages 33 V~ / 70 V.
| Easy handling with gloves | |
Other specifications :
Definitions (according to IEC 61010-031 standard, "Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031 Safety requirements for hand-held probe assemblies for electrical measurement and test") : CAT III (measurement category III) : measurements performed in the building installation. Examples are measurements on distribution boards, circuit-breakers, wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed installation, and equipment for industrial use and some other equipment, for example, stationary motors with permanent connection to the fixed installation. Reinforced insulation and double
insulation ( Pollution : addition of foreign matter, solid, liquid or gaseous (ionized gazes), that may produce a reduction of dielectric strength or surface resistivity. Pollution degree 2 : normally only non-conductive pollution occurs. Occasionally, however, a temporary conductivity caused by condensation must be expected. Breaking capacity : maximum current a fuse is able to break safely. The breaking capacity of the class CC fuses is more than one of the standard fuses ( 200 kiloAmpere against 120 kiloAmpere ) because they are intended to protect high power circuits. For this reason, they must not be replaced unintentionally by standard fuses else they may explode and create damages and hurts in case of overload. |
Measurement accessories from the Electrop-PJP's "IP2X" range compliant with the above tips :
 |
|
|
"Very high safety" products - IP2X connection.
Principle : to be able to connect the end of a lead's tip, unprotected, without any risk
for the operator. Meanwhile, the usual safety rules must be applied. (download our catalogue page ) |
|
|
||
 |
|
 |
|
| Test-clips, connection clamps.
|
P / N 6005-IP2X
|
Test-clips, connection
alligator clips.
|
P / N 6007-IP2X
|
|
|
||
 |
|
 |
|
| Test-clips, connection hook.
|
P / N 6008-IP2X
|
Rigid test-clips, connection
alligator clips.
|
P / N 6009-IP2X
|
|
|
 |
 |
 |
| |
|
||
 |
 20 A P / N 5450-IP2X |
 |
36 A P / N 405-IP2X |
| Alligator clips under rubber sheath. | Ø2 mm smooth test tip. Application : transforms a Ø4 mm connectable test tip into Ø2 mm smooth test tip. | ||
Special right angle connectors. Ø4 mm smooth tip stripped on 19 mm (0.75 in) (P / N 60619-IP2X) or 25 mm (0.98 in) (P / N 60625-IP2X). Example of application : connects onto terminals. |
 |
20 A P / N 60619-IP2X and 60625-IP2X |
| Contact : | Address : Electro PJP 31 rue Julien
Feuvrier BP366 F-39105 Dole France Phone : (33) Ø3 84 82 13 30, Fax : (33) Ø3 84 82 40 48 E-mail : mail@electro-pjp.com, Web : http://www.electro-pjp.com |
) : protection insulation equal to 2 basic insulations at
least. Required for any hand-held accessory.
